Anderic RR1001 User/Programming Guide
Aydan
Last Update 1 個月前
Program - Code Input Method
- Turn on the TV manually.
- Press and hold the [SET] and [POWER] keys simultaneously for 3 seconds; the indicator
light shall remain on, then release the keys. - Enter the 4-digit code of your brand TV from the code list at the end of this manual. After a valid code entry, the indicator turns off. The indicator flashes four times quickly for an invalid code and exits setup mode.
NOTE: After entering code setup mode, if without pressing any button for 10 seconds, the remote shall quit the setup mode.
Program – Shortcut Key Method
- Turn on the TV manually.
- Press and hold [SET] and the respective TV brand key from the chart below. (0-9, +100,
MUTE) simultaneously and continue to hold keys until the TV is powered off; the indicator light shall remain on for the duration;
Now the remote is automatically searching the code of that TV brand. If the TV is controlled (by powering on or turning it off), release the buttons to save the code and quit programming.
Shortcut Key - Brand Chart


Program – Manual Code Search
- Turn on the TV.
- Press and hold the [SET] key, then long press the [CH+] key for about 5 seconds until the
indicator light remains on. Release the keys. - Press and release the key [CH+] or [CH-], with each press code, will change. Longpressing the [CH+] or [CH-] key code will change faster. When the channel changes, please press the [SET] key quickly to save the code.
NOTE: Pressing [CH+] scrolls forward, while [CH-] scrolls backward through the code database. If no key is pressed in 10 seconds, the setting will be exited automatically during the setting process
Learning function
- Press and hold the [SET] key, then simultaneously long-press the [VOL+] key for about 5
seconds; the indicator light will light and remain on. Release the two keys. The remote is now in learning mode. - Point the original remote toward the RR1001. The distance should be within 1-3 cm, and the eyes of the remotes must directly align.
- Press the key you want to learn from the original remote control (the LED of RR1001 will keep flashing), then press any key of RR1001 to which you wish to assign the code. The indicator light will remain on.
- Repeat Step 2 to continue learning the other keys.
- When you have finished learning all the desired keys, press and hold the [SET] key, then simultaneously press the [VOL-] key, and the indicator light will go out. The learning will be saved and exited.
NOTE: During the learning process, if no keys are pressed in 25 seconds, the learning state will be exited without saving
Code Identification
- Press and hold the [SET] and [POWER] keys simultaneously for 3 seconds; the indicator light shall remain on, then release the keys.
- Input [9] [9] [0] with number keys. The indicator light will flash twice and turn off.
- Press the key [1], count the number of indicator light flashes, and write it down.
- Press the key [2], count the number of indicator light flashes, and write it down.
- Press the key [3], count the number of indicator light flashes, and write it down.
- Press the key [4], count the number of indicator light flashes, and write it down.
NOTE: If the code number is 0. The indicator light will not flash.
Factory Reset
Press and hold the [SET] and [POWER] keys simultaneously for 3 seconds; the indicator light shall
remain on, then release the keys.
Press the [CC] key and the light shall flash three times. The remote has now been reset to factory settings.
NOTE: The factory code can control 95% of the most popular TVs if the remote is reset to factory settings
Setting the Sleep Timer
NOTE: The SLEEP button operates the Sleep function of your TV, providing it supports the Sleep
function. Alternatively, with the instructions in this section, you can enable the remote to turn off
your TV after 1 to 99 minutes. This
- First, make sure you have your remote programmed to your TV using one of the above programming methods.
- After successfully programming your remote, try pressing the SLEEP button first and make sure the on-screen sleep option DOES NOT appear before continuing. If it does occur, you do not have to continue with the following steps.
- Press and hold the [SLEEP] key until the indicator light blinks and remains on. Then, release the key.
- Using the numerical pad, press numbers 01 - 99 depending on the minutes you would like before the TV turns off (Example: If you press 01, the TV will turn off in 1 minute). The indicator light will turn off. TV Sleep Timer is now set.
- Leave the remote pointing towards the TV with an unobstructed path.
NOTE: To cancel the sleep function, press and hold the [SLEEP] or [POWER] key for 3 seconds. Pressing any other additional buttons on the remote will not cancel the sleep timer
Setup Lock
- Press and hold the [SET] and [POWER] keys simultaneously for 3 seconds; the indicator
light will remain on, then release the keys. - Input code using keys [9] [9] [6] [6]; the indicator light shall flash five times. The remote is locked and cannot be programmed in any way unless these steps are repeated.
NOTE: to unlock the remote, repeat the above steps.
Code List









