Anderic RRU401.6 Full User Guide and Programming Instructions.

See below diagram for help with
installing the batteries

This method allows remote programming using codes from the
attached code list. 

1. Turn on the device you want to
   control. 
2. Find the corresponding brand code from the attached code list, and write it down. 
3. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key.
4. Input the 4-digit code from codebook; 

        a. If valid - Mode key light will go out directly;  

        b. If invalid - Mode key will blink three times quickly and go out, please                 try inputting the code again. 

 5. Check to see if most of the keys work to control your device, if not,    please try another code under the same brand & repeat all steps. You may also try “Auto code search method” or “One button search method” below. 

Note: During the programming mode, not pressing any button for 20 seconds will cause the remote to exit programming mode.

Allows for programming without codes
by scanning through all codes in the database. 

1. Turn on the device you want to control. 

2. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key. 

3. Press [CH+] or [CH-] key and release to search forward or backward. 

4. When the device powers off (or video starts playing), press [POWER] key to save and exit 

(During searching, you can press key [CH+] or [CH-] to change searching direction, and if press any other key, it will exit from searching mode).

Allows for programming by only
pressing a single key. Only works for
TV and Cable/STB codes. 

1. Power on the device you want to control. 
2. Press & release the mode key you wish to program (e.g., TV).
3. Find your corresponding brand number from the below list, press and hold the corresponding number key until the unit powers off. Once unit powers off, release the key. 
4.  Check other keys to see if most can work correctly.                                     If not, repeat steps 1-4

Note: while holding the number key, after 3 seconds the mode light goes out, it will enter the searching mode for that brand; mode light will now be flashing about once every second

Use this method to display the code
that is programmed. 

1. Press and release the mode key you would like know code for (e.g., TV). 
2. Press key “[MENU]” and “[1]”, the Mode key flash times indicate the first digit of the code. 
3. Press key “[MENU]” and “[2]”, the mode key flash times indicate the second digit of the code. 
4. Press key “[MENU]” and “[3]”, the mode key flash times indicate the third digit of the code. 
5. Press key “[MENU]” and “[4]”, the mode key flash times indicate the fourth digit of the code. 

NOTE: If the current digit is 0, the mode key will not flash.

When enabled, this feature allows for
powering on/off multiple devices with a single press of the POWER button. 

Enable - Multi-mode Combine Power 

1. Press and hold any mode key (e.g., TV) for about 3 seconds until mode key lights and remains on, release the mode key. 
2. Input code "9 9 8 0". Mode key remains lit. 
3. Press all mode keys (i.e., TV, STB, DVD) you wish to enable multi-mode combine power. 
4. Press [POWER] key to save and exit. 

Disable - Multi-mode Combine 

1. Press and hold any mode key (e.g., TV) for about 3 seconds until mode key lights and remains on, release the mode key. 
2. Input code "9 9 8 0". Mode key remains lit. 
3. Press [POWER] key to save and exit, Mode key blinks two times and goes out.

When enabled, this feature allows for
locking a device mode so that it cannot be re-programmed. It can is used as a safety feature for accidental programming. If enabled, device lock must be disabled first before mode can be programmed again. 

1. Press and hold the mode key (e.g., STB) you wish to enable/disable device mode lock for 3 seconds until the mode key lights and remains on, release the mode key. 
2. Input code “9 9 8 1”.

    a. If enabled - The mode light goes out directly 

    b. If disabled - The mode light blinks two times

When enabled, all channel keys: 0-9,
[-], [RECALL],[CC], [SAP], [CH +]& [CH -] will always send the code of mode assigned, no matter what mode the remote currently resides. 

Example: After programming channel punch-through to STB mode, if remote is presently in TV mode when pressing a channel key, remote will send the code for STB instead of TV. 

1. Press and hold the mode key (e.g., STB) you wish to enable/disable channel punch-through for about 3 seconds until mode key lights and remains on, release the mode key. 
2. Input code “9 9 8 2”. 

    a. If enabled - The mode light goes out directly. 

    b. If disabled - The mode light blinks two times.

When enabled, all volume keys:
[MUTE], [VOL+]&[VOL-] will always
send the code of mode no matter what mode the remote currently resides. 

1. Press and hold the mode key (e.g., TV) you wish to enable/disable volume punch-through for about 3 seconds until the mode key lights and remains on; release the mode key. 
2. Input code "9 9 8 3". a. If enabled - The mode light goes out directly.

    a. If enabled - The mode light goes out directly.

    b. If disabled - The mode light blinks two times.

When enabled, all media keys: [STOP],
[RECORD], [<<], [|<<], [PAUSE], [>>|], [>>], [PLAY] will always send code of mode assigned, no matter what mode the remote currently resides.

1. Press and hold the mode key (e.g., DVD) you wish to enable/disable media punch-through for  3 seconds until the mode key lights and remains on, release the mode key. 
2. Input code “9 9 8 4”. 

    a. If enabled - The mode light goes out directly. 

    b. If disabled - The mode light blinks two times.

When enabled, all Roku related keys:
[EXIT] ( ), [<<], [PLAY],[PAUSE], [>>], [INFO](*), [HOME],[REPLAY], [NETFLIX], [UP], [DOWN], [LEFT], [RIGHT]&[OK] will always send code of mode assigned, no matter what mode the remote currently resides. 

1. Press and hold the mode key (e.g., STB) you wish to enable/disable Roku punch-through for, for about 3 seconds until the mode key lights and remains on, release the mode key. 
2. Input code "9 9 7 0". 

    a. If enabled - The mode light goes out directly. 

    b. If disabled - The mode light blinks two times.

When enabled, all Roku related keys:
[EXIT] ( ), [<<], [PLAY],[PAUSE], >>], [INFO](*), [HOME], [REPLAY], [NETFLIX]will always send code of mode assigned, no matter what mode the remote currently resides.

1. Press and hold the mode key (e.g., TV) you wish to enable/disable Roku punch-through for about 3 seconds until the mode key lights and remains on, release the mode key. 
2. Input code "9 9 7 1". 

    a. If enabled - The mode light goes out directly. 

    b. If disabled - The mode light blinks two times.

Note: All-key punch-through has the lowest priority among all punch-through types. You may enable other punch-through modes to work alongside it, and they will have higher priority. 

1. Press and hold the mode key (e.g., TV) you wish to enable/disable all-key punch-through for about 3 seconds until the mode key lights and remains on; release the mode key. 
2. Input code "9 9 7 3". 

    a. If enabled - The mode light goes out directly. 

    b. If disabled - The mode light blinks two times.

Individual Key Punch-through allows
for individually assigning keys to “punch-through” to your chosen mode. After enabling punch through to a given key, the key will always send the code to the assigned device no matter what mode the remote currently resides. 

Note: Individual Key Punch-through has the highest priority among all punch-through types.

Enable - Individual Key Punch-through 

1. Press and hold any mode key (e.g., TV) for about 3 seconds until the mode key lights and remains on, and release the key. 
2. Input code “9 8”, 
3. Press the corresponding key you wish to enable punch-through for, 
4. Press the mode key you want to assign it to (e.g., TV, STB, AUX); the mode light goes out directly. 

Note: To re-assign a key to a different mode, repeat steps 1-4. 

Disable - Individual Key Punch-through 

1. Press and hold any mode key (e.g., TV) for about 3 seconds until mode key lights and remains on, release the key. 
2. Input code “9 0 0”, 
3. Press the key you want to disable the punch-through for; mode light blinks two times to confirm.

Learning allows for programming of
individual keys using your existing remote's codes. 

1. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key. 
2. Press and release the [MENU] key; the mode key blinks slowly, and the remote is now in learning mode. 
3. Press and release the key you want to be learned; mode light now remains on. 
4. 4. Align both remotes by pointing them at each other, with a distance of about 2 inches apart, with IR LEDs directly aligned. 5
5. . Press and hold the corresponding key on the target remote control until the mode light blinks three times and then flashes slowly. This means the code was learned successfully; continue to step 6. If unsuccessful, the mode light flashes two times quickly and exits from learning mode. This may indicate that there is not enough memory space. Please delete some learned keys. Please start over from step 1. 
6. Repeat steps 3-5 to learn all your needed keys while model light blinks slowly, then 
7. Press the mode key (e.g., TV) to save and exit.

Delete individual learned key 

1. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key. 
2. Press and release [MENU] key, the mode key blinks slowly, the remote is now in learning mode. 
3. Press and hold the key you want to delete learned code from, 

    a. If successful - The mode light blinks three times, remote saves and exits. 

    b. If unsuccessful - The mode light flashes two times and exits.

        Repeat steps  1-3

Delete all learned keys from a single device 

1. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key. 
2. Press and release [MENU] key, the mode key blinks slowly, the remote is now in learning mode. 
3. Press and hold the mode key you want to delete all learned keys from (e.g., TV) until the mode light blinks three times and exits.

Delete all learned keys from all devices 

1. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key. 
2. Input code "9 9 8 8", mode light blinks two times slowly to confirm and exits.

Macros allow for multiple keys to
transmit with the pressing of one dedicated key. Example, with a single press of the assigned key, the remote could Power on TV, Change input, Volume Increase, Power on Cable Box & Input channel 530. 

Setting a Macro Key while in a specific Mode only (Fixed Device) 

What is Fixed Device? 

This setting allows for assigning a macro key to be used while in the designated mode only. Example, if “FAV” key is assigned to “TV” mode to send macros. “FAV” key will operate as normal if remote is in any other mode such as STB, DVD or AUDIO. “FAV” key will only send the assigned macro if remote is in “TV” mode when the key is depressed. 

1. Press and hold the mode key (e.g., TV) you wish to program for about 3 seconds until the mode light remains on, release the mode key.
2. Input code "9 9 5", 
3. Press key to assign macro function to, the LED flashes once and remains on; 
4. Press the mode key (e.g., TV), then follow by pressing the keys in order in which you want the remote to transmit them. If you want to change modes during the sequence, press the corresponding mode key (e.g., DVD) in sequence and then continue with pressing remaining keys you wish. 
5. When complete, Press and hold any Mode key (e.g., TV) for about 3 seconds to save and exit.

Setting a Macro Key that works while in any mode (Non-fixed device) 

What is a non-fixed device? 

This setting allows for always sending the function of the macro key no matter what mode (i.e., TV, DVD, STB, AUDIO) the remote resides. 

1. Press and hold any mode key (e.g., TV) for about 3 seconds until the mode light remains on, release the mode key. 

2. Input code "9 9 6", 

3. Press key to assign macro function to, the LED flashes once and remains on; 

4. Press the mode key (e.g., TV), then follow by pressing the keys in order in which you want the remote to transmit them. If you want to change modes during the sequence, press the corresponding mode key (e.g., DVD) in sequence and then continue with pressing remaining keys you wish.

 5. When complete, Press and hold any Mode key (e.g., TV) for about 3 seconds to save and exit.

Example: Assigning “FAV” key to Power on TV, Change input, Increase volume by 1, Power on Cable Box, Input channel 530. Press the following keys in sequence: Hold [TV] for 3 seconds, [9], [9], [6], [FAV], [TV], [POWER], [INPUT], [VOL +], [CBL], [POWER], [5], [3], [0] & finally, press and hold [TV] for 3 seconds to save. Delete programmed macro key: Simply skip step 4 from above procedure.

Macro functionality notes: 

This remote allows up to 5 keys having macro functionality. 

This remote can program a maximum of 15 steps per each macro. 

If programming a macro over a previously assigned macro, it will replace it.

Toggle backlighting on/off 

1. Press and hold any mode key (e.g.,
   TV) for about 3 seconds until the mode light remains on, release the mode key. 
2. Input code "9 9 8 5"

1. Press and hold any mode key (e.g.,
   TV) for about 3 seconds until the mode light remains on, release the mode key. 
2. Input code "9 9 8 6".

1. Press and hold any mode key (e.g.,
   TV) for about 3 seconds until the mode light remains on, release the mode key.
2. Input code "9 9 8 7".

1. Press and hold any mode key (e.g.,
   TV) for about 3 seconds until the
   mode light remains on, release the mode key. 
2. Input code "9 9 9 9"; all mode lights will light and stay lit for about 3 seconds then go out to confirm successful reset. 

SEE LINK BELOW FOR CODE LIST

https://www.replacementremotes.com/store/productfiles/rru401-6-om.pdf

FOR ADDITIONAL HELP AND SUPPORTVISIT ANDERIC.COM. ANDERIC® IS A REGISTERED TRADEMARK OF DAN’S ELECTRONICS ETC. INCORPORATED. ALL RIGHTS RESERVED.