Anderic RRCM7500 Operating and Programming Instructions

Thank you for purchasing the Anderic RRCM7500 Universal remote control designed to work with CM7500XRC2 Channel Master DVR. Please see the below information to learn how to program and operate your remote control. 

This remote control is specifically designed to work with Channel Master DVR set-top boxes, including the models CM7001, CM7004, CM7500GB16, CM7500TB1, and CM7500XRC2. 

The Anderic RRCM7500 is not programmable for any other DVR models. 

Additionally, the RRCM7500 allows you to program secondary devices, such as TVs and audio equipment. Please refer to the programming instructions below for details on how to set up these devices.

Please insert two AA batteries into the battery compartment behind the battery door on the back of the remote. You may need to remove the screw securing the battery cover. Please make sure to match polarities when installing the batteries. Slide the battery cover down toward the bottom of the remote to remove it, then replace it after installing the batteries. The battery cover screw is optional and is not needed to secure the battery cover to the remote. 

This remote has an optional security cable (sold separately) attachment. You can purchase this security cable from Anderic.com. Part number: CBL01. 

1. Turn on the device you want to control.

2. Find the corresponding brand code from the attached code list and write it down.

3. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key

4. Input the 4-digit code from the code list.
   If valid - the indicator light will go out directly.

   If invalid - the indicator light will blink three times quickly and go out; please try inputting the code again.

5. Check to see if most of the keys work to control your device; if not, please try another code under the same brand & repeat all steps. You may also try the “Code search method.”

Note: During the programming mode, not pressing any button for 20 seconds will cause the remote to exit the programming mode. 

1. Turn on the device you want to control.

2. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key.

3. Press & hold the [RED-COLORED] (for TV) key or the [GREEN-COLORED] key (For AUDIO); it will enter “Code search method.”

4. Release the key [RED-COLORED] (for TV) key or the [GREEN-COLORED] key (For AUDIO) when the device has a response.

5. Check to see if most of the keys work to control your device; if not, please repeat all steps above. 

1. Turn on the device you want to control.

2. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key.

3. Input code 991(forTV) or 992 (For AUDIO).

4. Find your corresponding brand number from the below list, and press and hold the corresponding number key.

5. Once the unit responds, release the key and press any key to save.

6. Panasonic 

Note: This feature allows for always locking the input key to send the code to the programmed TV or Set-top-box device regardless of the mode selected.

1. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key.

2. Press the [INPUT] key, and the indicator light blinks once and remains illuminated.

3. Press the device key [RED-COLORED] for the TV or [GREEN-COLORED] for the set-top box. 

Note: This feature allows locking the VOL+, VOL-, and MUTE keys to always send the code to the programmed TV or Set-top-box device regardless of the remote’s mode.

1. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key.

2. Press the [VOL+] key, and the indicator light blinks once and remains illuminated.

3. Press the device key [RED-COLORED] for the TV or [GREEN-COLORED] for the set-top box. 

Note: this feature allows for locking the codes programmed in place, requiring an extra step to avoid accidentally having the codes changed.

1. Press & hold the [RED-COLORED] key and the [OK] keys simultaneously for about 3 seconds until the indicator light flashes twice; release the keys.
1. Enabled: Code input or code search method cannot change the device code 
2. Disabled: Code input or code search method can program the code as normal. Repeating these steps will shift between enabled and disabled 

Press & hold the [OK] key and the [YELLOW-COLORED] key simultaneously for about 3 seconds until the indicator light flashes once; release the keys. 

If the LED indicator flashes ten times when you press any key, it indicates the low voltage. Please replace the batteries. 

Press & hold the [OK] and [ON] keys simultaneously for about 3 seconds until the indicator light flashes twice; release the two keys. 

Note: deactivating the backlighting feature will conserve battery consumption.
Press & hold the [OK] and [BLUE-COLORED] keys simultaneously for about 3 seconds until the indicator light flashes twice; release the two keys. 

Go to Anderic.com/RRCM7500 for help and support. Anderic is a registered trademark of Dan’s Electronics Etc., Inc. All brands mentioned in this document are registered trademarks of their respective owners. Dan’s Electronics Etc., Inc. has no affiliation with other brands.

Copyright Anderic® 2024

CLICK HERE TO VIEW THE CODE LIST