[User Guide] Anderic RRH100 & RRHC100 Hospitality TV 1-Device Universal Remote Control
Aydan
Last Update 6 maanden geleden
Introduction
With the purchase of this remote, you should receive a screw for the battery cover. The battery cover screw is optional; the battery cover does not need the screw to hold it in place. This remote requires two AAA-size batteries, which are not included.
This user guide does not have the Code List. For the Code List, please go to the below URL: https://anderic.tawk.help/article/rrh100-rrhc100-code-list

Optional Security Cable Attachment
Optional Security Cable:
- Part number: CBL01
The cable can be easily attached under the battery cover for a secure and seamless appearance.

Programming the remote: Direct Code Input Method
NOTE: The RRH100/C100 are Pre-programmed to work with LG and Vizio TVs. As well as STB-2000 Set-top-Boxes (Bed code 0) when the STB mode is unlocked. Click here to view the code list.
- Find and write down the codes from the code list here.
- Turn on the device you want to control, and find the corresponding brand code from the attached code list.
- Press and release the device mode key you would like to program ([TV] or [STB]).
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the
indicator light lights and remains on, release both keys. - Input the four-digit code. If the remote successfully saves the code, the indicator light will go out. If there is an error, the indicator light will blink slowly three times and go out. Repeat steps 1-4.
*Please check if most remote control keys can control the device. If not, please restart steps
1-4 using a different code.
*After trying all the codes for your brand without success, please try the “Programming the remote—Code Search” method below.
Note: During the programming mode, pressing any button other than the number buttons or not
pressing any button for 10 seconds will cause the remote to exit programming mode.
Programming the remote: Code Search Method
- Turn on the device you want to control.
- Press and release the device mode key you would like to program ([TV] or [STB]).
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until
the indicator light lights and remains on, release both keys. - Repeatedly Press [CH+] to search forwards or [CH-] to search backward; remote will
send the code of POWER one by one. - When the device is turned off, immediately press the [S] button to save and exit.
Code Display
- Press and release keys [MUTE] and [1] simultaneously, then release. The indicator light
flashing times represent the first digit of the code. Note: If the digit is 0, the indicator light will not flash. - Press and release keys [MUTE] and [2] simultaneously, then release. The indicator light flashing times represent the second digit of the code.
- Press and release keys [MUTE] and [3] simultaneously, then release. The indicator light flashing times represent the third digit of the code.
- Press and release keys [MUTE] and [4] simultaneously, then release. The indicator light flashing times represent the fourth digit of the code.
Note: If the digit is 0, the indicator light will not flash.
Single Press Combined POWER Key
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the
indicator light lights and remains on, release both keys. - Device mode indicator light will light. It doesn’t matter which mode lights.
- Input code [9] [9] [9] [5]. a. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “one key power-off all devices” was successfully enabled.
- Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits, this indicates that “one key power-off all devices” was successfully disabled.
Note: After one key power-off all devices successfully enabled, press [POWER] key, it will send STB Power immediately followed by TV Power code.
STB (set-top-box) Punch-Through Function
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the
indicator light lights and remains on, release both keys. - Device mode indicator light will light. It doesn’t matter which mode lights.
- Input code [9] [9] [9] [0]. a. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “STB punch-through” was successfully enabled.
- Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits; this indicates that “STB punch-through” was successfully disabled.
TV Punch-Through Function
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the
indicator light lights and remains on, release both keys. - Device mode indicator light will light. It doesn’t matter which mode lights.
- Input code [9] [9] [9] [1]. a. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “TV punch-through” was successfully enabled.
- Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits; this indicates that “TV punch-through” was successfully disabled
Individually assign key punch-through Lock
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the
indicator light lights and remains on, release both keys. - Input the 2 digits code [9] [8].
- Press the button you want to lock.
- Press the device mode button you want to assign it to (e.g. [TV] or [STB]). If successful, the indicator light will turn off directly after pressing the Mode button. Repeat steps 1 – 4 for each button lock.
Individually Assign Punch-through Unlock
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input the three digits [9] [0] [0],
- Press the button you want to unlock the punch-through, the indicator light will blink one time
& turn off.
Device Mode Lock
- Press and release the device mode key you would like to lock code for ([TV] or [STB]).
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input code [9] [9] [9] [9],
a. Locked - If the indicator light turns off directly after 4 digits input, it indicates mode successfully locked. b. Unlocked - If the indicator light blinks 2 times and turns off after 4 digits input, it indicates mode successfully unlocked.
Reset to Factory Default Status - Unchanging 1-Device/2-DeviceStatus
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input code [9] [9] [9] [6]. The indicator light will turn off, indicating that the remote has been
reset to factory default status
Reset to Factory Default Status
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input code [9] [7] [6] [0]. The indicator light will turn off, indicating that the remote has been
reset to factory default status
Advanced Option: Shift remote to 1-Device; TV only remote.
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input code [9] [7] [6] [1]. The indicator light will blink 3 times, indicating that the remote has
successfully been reset to factory default status and converted to a 1-Device remote.
Advanced Option: Shift remote to 2-Device; TV/STB remote.
- Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
- Input code [9] [7] [6] [2]. The indicator light will blink 3 times, indicating that the remote has
successfully been reset to factory default status and converted to a 2-Device remote.
Admiral, Advent, Akai, AOC, ApexDigital, Audiovox, Aventura, Broksonic, Carver, Celebrity, Celera, Changhong, Coby, CommercialSolutions, Crosley, Curtis, CurtisMathes, Daewoo, Dell, Denon, Dumont, Durabrand, Dynex, Electroband, Electrograph, Electrohome, Element, Emerson, Emprex, Envision, ESA, Funai, Gateway, GE, GFM, Gibralter, GoldStar, Haier, Hallmark, Hannspree, Harman/Kardon, Havermy, HelloKitty, Hisense, Hitachi, iLo, Infinity, Insignia, Inteq, JBL, JCB, Jensen, JVC, KDS, KLH, LG, LXI (code 1922), MAG, Magnavox, Marantz, Matsushita, Maxent, MBQuart, Megatron, Memorex, MGA, Midland, Mitsubishi, Motorola, MTC, NAD, NEC, NetTV, NexusElectronics, Nikko, Norcent, Olevia, Optimus, Optoma, Optonica, Orion, Panasonic, PARK, Penney, Petters, Philco, Philips, Pioneer, Polaroid, Portland, Prima, Prism, Proscan, Proton, Proview, Pulsar, Quasar, RadioShack, RCA, Realistic, Runco, Sampo, Samsung, Sansui, Sanyo, Sceptre, Scotch, Scott, Sears, Sharp, ShengChia, Signature, Sony, Soundesign, Soyo, Spectroniq, Squareview, Superscan, Supreme, SVA, Sylvania, Symphonic, Syntax, Tandy, TCL (code 2113), Technics, Techwood, Teknika, Telefunken, TMK, TNCi, Toshiba, TVS, Victor, Vidikron, Vidtech, Viewsonic, Viore, Vizio, Wards, Waycon, Westinghouse, WhiteWestinghouse, Wyse, Zenith (doesn't work Sigmac), LG STB-2000 Set-Top-Box
Specifications
Part Number: CBL01
Dimensions: 1.00 x 5.00 x 0.50 (W x L x D, inches)